Latest [Sep 29, 2021] NSE7_SDW-6.4 Exam with Accurate Fortinet NSE 7 - SD-WAN 6.4 PDF Questions
Take a Leap Forward in Your Career by Earning Fortinet 37 Questions
NEW QUESTION 18
Refer to exhibits.
Exhibit A shows the performance SLA exhibit B shows the SD-WAN diagnostics output.
Based on the exhibits, which statement is correct?
- A. SD-WAN member interfaces are affected by the SLA state of the inactive interface
- B. The SLA state of port1 is dead after five unanswered requests by the SLA servers.
- C. Port1 became dead 1ecause no traffic was offload through the egress of port1.
- D. Both SD-WAN member interfaces have used separate SLA targets.
Answer: B
NEW QUESTION 19
Which two statements describe how IPsec phase 1 main mode is different from aggressive mode when performing IKE negotiation? (Choose two )
- A. XAuth is enabled as an additional level of authentication, which requires a username and password.
- B. A peer ID is included in the first packet from the initiator, along with suggested security policies.
- C. The use of Diffie Hellman keys is limited by the responder and needs initiator acceptance.
- D. A total of six packets are exchanged between an initiator and a responder instead of three packets.
Answer: A,D
NEW QUESTION 20
What are the two minimum configuration requirements for an outgoing interface to be selected once the SD-WAN logical interface is enabled? (Choose two )
- A. Specify outgoing interface routing cost.
- B. Specify incoming interfaces in SD-WAN rules.
- C. Configure SD-WAN rules interface preference.
- D. Select SD-WAN balancing strategy.
Answer: C
NEW QUESTION 21
Which three parameters are available to configure SD-WAN rules? (Choose three.)
- A. Internet service database (ISDB) address object
- B. Type of physical link connection
- C. URL categories
- D. Application signatures
- E. Source and destination IP address
Answer: A,B,E
NEW QUESTION 22
Refer to exhibits.
Exhibit A.
Exhibit B.
Exhibit A shows the traffic shaping policy and exhibit B show: the firewall policy FortiGate is not performing traffic shaping as expected basi on the policies shown in the exhibits.
To correct this traffic shaping issue on FortiGate, what configuration change must be made on which policy?
- A. The URL category must be specified on the traffic shaping policy
- B. The application control profile must be enabled on the firewall policy.
- C. The shaper mode must be applied per-IP shaper on the traffic shaping policy
- D. The web filter profile must be enabled on the firewall policy
Answer: D
NEW QUESTION 23
Refer to the exhibit.
Which statement about the command route-tag in the SD-WAN rule is true?
- A. It uses route tags for a BGP community and assigns the SD-WAN rules with same tag.
- B. It enables the SD-WAN rule to load balance and assign traffic with a route tag
- C. It ensures route tags match the SD-WAN rule based on the rule order
- D. It tags each route and references the tag in the routing table.
Answer: C
NEW QUESTION 24
Refer to the exhibit.
Multiple IPsec VPNs are formed between two hub-and-spokes groups, and site-to-site between Hub 1 and Hub 2 The administrator configured ADVPN on the dual regions topology
Which two statements are correct if a user in Toronto sends traffic to London? (Choose two )
- A. Toronto needs to establish a site-to-site tunnel with Hub 2 to bypass Hub 1.
- B. The first packets from Toronto to London are routed through Hub 1 then to Hub 2.
- C. London generates an IKE information message that contains the Toronto public IP address
- D. Traffic from Toronto to London triggers the dynamic negotiation of a direct site-to-site VPN
Answer: A,D
NEW QUESTION 25
In the default SD-WAN minimum configuration, which two statements are correct when traffic matches the default implicit SD-WAN rule? (Choose two )
- A. Matched traffic failed RPF and was caught by the rule.
- B. An absolute SD-WAN rule was defined and matched traffic.
- C. Traffic has matched none of the FortiGate policy routes.
- D. The FIB lookup resolved interface was the SD-WAN interface.
Answer: C,D
NEW QUESTION 26
Refer to exhibits.
Exhibit A shows the source NAT global setting and exhibit B shows the routing table on FortiGate.
Based on the exhibits, which two statements about increasing the port2 interface priority to 20 are true? (Choose two.)
- A. All the existing sessions will be blocked from using port1 and port2.
- B. All the existing sessions using SNAT will be flushed and routed through port1.
- C. All the existing sessions will continue to use port2, and new sessions will use port1.
- D. All the existing sessions that do not use SNAT will be flushed and routed through port1.
Answer: B,C
NEW QUESTION 27
Refer to exhibits.
Exhibit A.
Exhibit B.
Exhibit A, which shows the SD-WAN performance SLA and exhibit B shows the health of the participating SD-WAN members.
Based on the exhibits, which statement is correct?
- A. The SLA state of port2 has exceeded three consecutive unanswered requests from the SLA server.
- B. Port2 needs to wait 500 milliseconds to change the status from alive to dead.
- C. Check interval is the time to wait before a packet sent by a member interface considered as lost.
- D. The dead member interface stays unavailable until an administrator manually brings the interface back.
Answer: A
NEW QUESTION 28
Which diagnostic command you can use to show interface-specific SLA logs for the last 10 minutes?
- A. diagnose sys virtual-wan-link health-check
- B. diagnose sys virtual-wan-link intf-sla-log
- C. diagnose sys virtual-wan-link sla-log
- D. diagnose sys virtual-wan-link log
Answer: C
Explanation:
Explanation/Reference: https://docs.fortinet.com/document/fortigate/6.2.0/cookbook/943037/sla-logging
NEW QUESTION 29
Which statement reflects how BGP tags work with SD-WAN rules?
- A. BGP tags match the SD-WAN rule based on the order that these rules were installed.
- B. VPN topologies are formed using only BGP dynamic routing with SD-WAN
- C. Route tags are used for a BGP community and the SD-WAN rules are assigned the same tag
- D. BGP tags require that the adding of static routes be enabled on all ADVPN interfaces
Answer: A
NEW QUESTION 30
Refer to the exhibit.
FortiGate has multiple dial-up VPN interfaces incoming on port1 that match only FIRST_VPN.
Which two configuration changes must be made to both IPsec VPN interfaces to allow incoming connections to match all possible IPsec dial-up interfaces? (Choose two.)
- A. Configure the IKE mode to be aggressive mode.
- B. Use different proposals are used between the interfaces.
- C. Specify a unique peer ID for each dial-up VPN interface.
- D. Use unique Diffie Hellman groups on each VPN interface.
Answer: B,D
NEW QUESTION 31
What are the two minimum configuration requirements for an outgoing interface to be selected once the SD-WAN logical interface is enabled? (Choose two )
- A. Specify incoming interfaces in SD-WAN rules.
- B. Configure SD-WAN rules interface preference.
- C. Select SD-WAN balancing strategy.
- D. Specify outgoing interface routing cost.
Answer: B,D
NEW QUESTION 32
Refer to the exhibit.
Which two statements about the status of the VPN tunnel are true? <Choose two )
- A. FortiGate created a single IPsec virtual interface that is shared by all clients
- B. 100.64.3.1 is one of the remote IP address that comes through index interlace 1.
- C. VPN static routes are prevented from populating the FortiGate routing table
- D. There are separate virtual interfaces for each dial-up client
Answer: D
NEW QUESTION 33
Refer to exhibits.
Exhibit A.
Exhibit B.
Exhibit A shows the SD-WAN rules and exhibit B shows the traffic logs. The SD-WAN traffic logs reflect how FortiGate processed traffic.
Which two statements about how the configured SD-WAN rules are processing traffic are true? (Choose two.)
- A. The implicit rule overrides all other rules because parameters widely cover sources and destinations.
- B. The initial session of an application goes through a learning phase in order to apply the correct rule
- C. SD-WAN rules are evaluated in the same way as firewall policies: from top to bottom
- D. The All_Access_Rules rule load balances Vimeo application traffic among SD-WAN member interfaces
Answer: A,B
NEW QUESTION 34
Refer to the exhibit.
Based on output shown in the exhibit, which two commands can be used by SD-WAN rules? (Choose two.)
- A. set priority 10.
- B. set cost 15.
- C. set source 100.64.1.1.
- D. set load-balance-mode source-ip-based.
Answer: A,D
NEW QUESTION 35
Refer to the exhibit.
What must you configure to enable ADVPN?
- A. The protected subnets should be set to address object to all (0.0 .0. o/o).
- B. ADVPN should only be enabled on unmanaged FortiGate devices.
- C. On the hub VPN, only the device needs additional phase one sett
- D. Each VPN device has a unique pre-shared key configured separately on phase one
Answer: D
NEW QUESTION 36
Refer to exhibits.
Exhibit A.
Exhibit B.
Exhibit A shows the source NAT global setting and exhibit B shows the routing table on FortiGate Based on the exhibits, which two statements about increasing the port2 interface priority to 20 are true? (Choose two )
- A. All the existing sessions will continue to use port2 and new sessions will use port1
- B. All the existing sessions will be blocked from using port1 and port2
- C. All the existing sessions with no SNAT will start using port1 as the outgoing interface instead of port2
- D. All the existing sessions using SNAT will start using port1 as the outgoing interface instead of port2.
Answer: C,D
NEW QUESTION 37
Refer to the exhibit.
What must you configure to enable ADVPN?
- A. The protected subnets should be set to address object to all (0.0 .0. o/o).
- B. ADVPN should only be enabled on unmanaged FortiGate devices.
- C. On the hub VPN, only the device needs additional phase one sett
- D. Each VPN device has a unique pre-shared key configured separately on phase one
Answer: D
NEW QUESTION 38
Refer to exhibits.
Exhibit A.
Exhibit B.
Exhibit A shows the traffic shaping policy and exhibit B show: the firewall policy FortiGate is not performing traffic shaping as expected basi on the policies shown in the exhibits.
To correct this traffic shaping issue on FortiGate, what configuration change must be made on which policy?
- A. The URL category must be specified on the traffic shaping policy
- B. The application control profile must be enabled on the firewall policy.
- C. The shaper mode must be applied per-IP shaper on the traffic shaping policy
- D. The web filter profile must be enabled on the firewall policy
Answer: D
NEW QUESTION 39
Which statement defines how a per-IP traffic shaper of 10 Mbps is applied to the entire network?
- A. The 10 Mbps bandwidth is shared equally among the IP addresses.
- B. A single user uses the allocated bandwidth divided by total number of users.
- C. Each IP is guaranteed a minimum 10 Mbps of bandwidth
- D. FortiGate allocates each IP address a maximum 10 Mbps of bandwidth.
Answer: D
Explanation:
Reference:
https://docs.fortinet.com/document/fortigate/6.2.0/cookbook/885253/per-ip-traffic-shaper
NEW QUESTION 40
An administrator is troubleshooting VoIP quality issues that occur when calling external phone numbers The SD-WAN interface on the edge FortiGate is configured with the default settings, and is using two upstream links One link has random jitter and latency issues and is based on a wireless connection Which two actions must the administrator apply simultaneously on the edge FortiGate to improve VoIP quality using SD_WAN rules?
- A. Choose the suitable interface based on the interface cost and weight
- B. Select the corresponding SD-WAN balancing strategy in the SD-WAN rule
- C. Place the troublesome link at the top of the interface preference list.
- D. Configure an SD-WAN rule to load balance all traffic without VoIP
- E. Use the performance SLA targets to detect latency and jitter instantly.
Answer: A,E
NEW QUESTION 41
What are two reasons why FortiGate would be unable to complete the zero-touch provisioning process? (Choose two.)
- A. The zero-touch provisioning process has completed internally, behind FortiGate.
- B. A factory reset performed on FortiGate.
- C. FortiDeploy has connected with FortiGate and provided the initial configuration to contact FortiManager
- D. The FortiGate cloud key has not been added to the FortiGate cloud portal.
- E. FortiGate has obtained a configuration from the platform template in FortiGate cloud.
Answer: A,D
NEW QUESTION 42
An administrator is troubleshooting VoIP quality issues that occur when calling external phone numbers The SD-WAN interface on the edge FortiGate is configured with the default settings, and is using two upstream links One link has random jitter and latency issues and is based on a wireless connection Which two actions must the administrator apply simultaneously on the edge FortiGate to improve VoIP quality using SD_WAN rules?
- A. Configure an SD-WAN rule to load balance all traffic without VoIP.
- B. Place the troublesome link at the top of the interface preference list.
- C. Select the corresponding SD-WAN balancing strategy in the SD-WAN rule.
- D. Choose the suitable interface based on the interface cost and weight.
- E. Use the performance SLA targets to detect latency and jitter instantly.
Answer: C,E
NEW QUESTION 43
......
Authentic Best resources for NSE7_SDW-6.4 Online Practice Exam: https://www.testinsides.top/NSE7_SDW-6.4-dumps-review.html